Galvanized Dual Pipe Support for Wood Beams

1 review
  • Fits 2 3/8 in. OD (2 in. ID) drive pipes
  • Fits 2 in. cable winders
  • Made of hot-dipped galvanized steel
  • Mounting brackets adjust up to 16 in. to fit most overhead wood beams
  • Features two sleeves with 1/4 in. grease fittings
  • Includes L-Bracket mounting fasteners
  • Does not include wood beam/joist mounting fasteners

From$113.90

Clear Selection and Start Over

About this Item

  • Fits 2 3/8 in. OD (2 in. ID) drive pipes
  • Fits 2 in. cable winders
  • Made of hot-dipped galvanized steel
  • Mounting brackets adjust up to 16 in. to fit most overhead wood beams
  • Features two sleeves with 1/4 in. grease fittings
  • Includes L-Bracket mounting fasteners
  • Does not include wood beam/joist mounting fasteners

Galvanized Dual Pipe Support for Wood Beams

The Galvanized Dual Pipe Support for Wood Beams mounts directly to overhead wood beams or joists. The supports are stamped and laser cut. Features an 18 in. distance from sleeve to sleeve. 2 in. cable winders will fit between the sleeves. The sleeves have (1) 1/4 in. press-in grease fitting offset from each sleeve. Allows the drive pipe to be greased without uninstalling the drive pipe. The sleeves will accept a 2 3/8 in. OD (2 in. ID) drive pipe.  The pipe support sleeves are measured out to line up with the boat hoist with minor adjustments.

The oversized sleeve reduces friction and ensures better load distribution. The sleeve keeps the drive pipe from walking up the side of the sleeve. Made from hot-dipped galvanized steel. The L-Brackets have (3) 3/4 in. round wood beam mounting holes and (1) 2 in. pipe support mounting slot. The entire kit weighs 17.15 pounds. The dual-pipe support measures 25 in. ( L) x 3 1/2 in. (W) x 6 in. (H). The L-Bracket measures 3 3/4 in. (L) x 2 1/2 in. (W) x 9 1/2 in. (H). The sleeves measure 3 1/2 in. (L) x 2 13/16 in. (W) x 2 13/16 (H) Recommended for virtually any type of overhead boat lift. Pipe support mounting fasteners included. Wood Beam / Joists mounting fasteners not included.

Includes:

(2) L-Brackets for Wood Beams
(1) Dual Pipe Support
(2) #12232 – 9/16 in. x 1 3/4 in. Galvanized Hex Head Bolts
(2) #17547 – 9/16 in. Galvanized Lock Washers
(4) #36427 – 9/16 in. Galvanized Flat Washers
(2)#36426 – 9/16 in. Galvanized Nuts

Specifications

Pipe Support (w/o L-Brackets) Dimensions: 25 in. (L) x 3 1/4 in. (W) x 6 in. (H)
Pipe Support Type: Dual
Pipe Support Material: Steel
Pipe Support Finish: Hot-Dipped Galvanized
Pipe Support Sleeve Diameter: 2 7/8 in. (OD) / 2 3/8 in. (ID)
Sleeve Fits Drive Pipes: 2 3/8 in. (OD) / 2 in. (ID)
Sleeve Dimensions: 3 in. (L) x 2 13/16 in. (W) x 2 13/16 in. (H)
Between Sleeves: 18 in.
Grease Fitting Size: 1/4 in.
Grease Fitting Amount: 2
Grease Fitting Placement: Offset
Grease Fitting Type: Press-In
Pipe Support Sleeve Thickness: 1/4 in.
Pipe Support L-Bracket Mounting Slots: 4
Pipe Support L-Bracket Mounting Slot Size: 2 in.
L-Bracket Dimensions: 3 3/4 in. (L) x 2 1/2 in. (W) x 9 1/2 in. (H)
L-Bracket Adjusts to: 2 in. - 16 in.
Cable Winder Type:: Varies
Cable Winder Fits: 2 in.
L-Bracket Amount: 2
Wood Beam Mounting Holes (Per L-Bracket): 3
Wood Beam Mounting Hole Size (Per L-Bracket): 3/4 in.
Drive Pipe Mounting Holes (Per L-Bracket): 1
Mounting Fasteners: Included (L-Brackets to Pipe Support Only)
Hex Head Bolt Amount: 2
Hex Head Bolt Size: 9/16 in. x 1 3/4 in.
Hex Head Bolt Finish: Zinc-plated Galvanized
Flat Washer Amount: 4
Flat Washer Size: 9/16 in.
Flat Washer Finish: Zinc-plated Galvanized
Lock Washer Amount: 2
Lock Washer Size: 9/16 in.
Lock Washer Finish: Zinc-plated Galvanized
Nut Amount: 2
Nut Thread: 12
Nut Size: 9/16 in.
Nut Finish: Zinc-plated Galvanized
Side Mount Rating: 1,000 lbs.
Side Mount Configuration: Straight-line
Twin Mount Rating: 1,500 lbs.
Side Mount Configuration: Straight-line
Center Mount Rating: 4,000 lbs.
Weight 17.15 lbs.
Center-mount pipe supports are only recommended for center mount or twin mount installations, never use a center mount pipe support on a side mount installation. Never attempt to straight-line lift any more than 4500 lbs on a side mount overhead lift or straight line more than 6000 lbs on center or twin mount lifts. Only use the full length of the pipe to connect both pipe supports. Do not attempt to use two short pieces of the drive pipe. If designing or engineering your own overhead lift you must download and read the BH-USA overhead lift guide that can be found on this page and in the tech guide section. BH-USA makes available complete engineered and rated lifts and highly encourages choosing this option over designing and engineering a lift on your own. The above ratings of the dual pipe supports are only valid if installing or using the pipe supports in accordance with the BH-USA overhead lift guide. The Side Mount and Twin Mount ratings are based on straight line pull, by compounding the cable you will increase the rating. Rating is based PR pipe support and not pr lift. When considering the weight of your boat you must use full wet weight plus the weight of cradle .

Tech Guides

Overhead Boat Lift Guide Dual Pipe Support Guide

Reviews

1 review for Galvanized Dual Pipe Support for Wood Beams

Rated 5 Out of 5

5 star
100%
4 star
0%
3 star
0%
2 star
0%
1 star
0%

  1. a

    shelia

Email Cart
Your Shopping Cart will be saved and you'll be given a link. You, or anyone with the link, can use it to retrieve your Cart at any time.
Back Email Cart
Your Shopping Cart will be saved with Product pictures and information, and Cart Totals. Then send it to yourself, or a friend, with a link to retrieve it at any time.
Your cart email sent successfully :)

Back to Top