Dual Pipe Support Kit for Aluminum Beams

  • Made from 6061-T6 marine-grade US aluminum
  • Mounts to standard 6″ x 4″ flange aluminum beam
  • More than 19″ between sleeves
  • Grease fitting installed on both sleeves
  • Aluminum beam mount

$203.57

7 in stock

About this Item

  • Made from 6061-T6 marine-grade US aluminum
  • Mounts to standard 6″ x 4″ flange aluminum beam
  • More than 19″ between sleeves
  • Grease fitting installed on both sleeves
  • Aluminum beam mount

Dual Pipe Support Kit for Aluminum Beams

The Dual Pipe Support Kit works with the Coastal Series overhead boat lifts. Slides on the aluminum structural beams. Fits 6 in. Web x 4 in. flange beam. The two welded sleeves include 1/4 in. grease fittings at the bottom of the sleeves. Allows for easier greasing.

The sleeves prevent the pipe from walking up the side. Guarantees a truer alignment. Allows plenty of room for an optional cable winder. More than 19 inches between each sleeve. Includes stainless steel fasteners.

Dual pipe supports, with or without hoist hanger, is best used in a center mount configuration. A 4,000 lb. maximum rating per hoist hanger when used correctly in center mounting. Side mounting greatly reducts the dual pipe support and hoist hanger capacity. A 1,000 lb. maximum rating when used correctly in side mounting. See the attached guide for more information and limitations.

Specifications

Dimensions: 25 1/4 in. L x 9 1/16 in. W x 6 5/8 in.
Weight: 9.7 lbs.
Between Sleeves: 18 3/4 in.
Material: Aluminum
Type: 6061-T6 US
Fastener Material: Stainless steel
Fastener Size: 1/2 in.
Bolt Type: Tap bolt
Bolt Size: 1/2 in. x 1 3/4 in.
Bolt Amount: 4
Washer Type: Lock
Washer Amount: 4
Washer Size: 1/2 in.
Washer Type: Flat
Washer Amount: 4
Washer Size: 1/2 in.
Nut Amount: 4
Nut Size: 1/2 in.
Center Mout Maximum Rating: 4,000 lbs.
Side Mount Maximum Rating: 1,000 lbs.
Center-mount pipe supports are only recommended for center mount or twin mount installations. It is not recommended to use pipe support on a side mount installation. Never attempt to straight-line lift any more than 4000 lbs on a side mount overhead lift or straight line more than 6000 lbs on center or twin mount lifts. Only use the full length of the pipe to connect both pipe supports.  Do not attempt to use two short pieces of the drive pipe. If designing or engineering your overhead lift, you must download and read the BH-USA overhead boat lift guide that can be found on this page. Also available in the tech guide section. BH-USA makes available complete engineered and rated lifts and highly encourages choosing this option over designing and engineering a boat lift on your own.  The above ratings of the dual pipe supports are only valid if installing or using the pipe supports with the BH-USA overhead boat lift guide. The Side Mount and Twin Mount ratings are based on straight line pull. Rating is based on per pipe support and not per boat lift. When considering the weight of your boat, you must use full wet weight plus the weight of the boat cradle. (wet weight + boat cradle weight = total lifting weight) BH-USA engineers and manufactures factory-rated complete boat lifts. We highly recommend purchasing one of these boat lifts instead of building your own. If you, or your installer, buys parts and pieces to engineer your custom boat lift, it will no longer be considered a Boat Hoist USA engineered boat lift.

Tech Guides

Overhead Boat Lift Guide Dual Pipe Support Guide Wakeboard Compounding Letter

Reviews

0 review for #Dual Pipe Support Kit for Aluminum Beams

Email Cart
Your Shopping Cart will be saved and you'll be given a link. You, or anyone with the link, can use it to retrieve your Cart at any time.
Back Email Cart
Your Shopping Cart will be saved with Product pictures and information, and Cart Totals. Then send it to yourself, or a friend, with a link to retrieve it at any time.
Your cart email sent successfully :)

Back to Top