BH-360 Fresh Water Belt Driven PWC Lift

11 reviews
  • Strongest PWC Lift Available
  • Low Profile Design
  • Fully Rotational
  • Hot Dipped Galvanized
  • Complete PWC Lift


Clear Selection
SKU: N/A Category:

About this Item

  • Strongest PWC Lift Available
  • Low Profile Design
  • Fully Rotational
  • Hot Dipped Galvanized
  • Complete PWC Lift

BH-360 Fresh Water Belt Driven PWC Lift

The BH-360 Fresh Water Belt Driven PWC Lift is made out of hot dipped galvanized steel with a lifting capacity of 1250 pounds. The fully rotating cradle travels on the galvanized ride pipe. It is mountable on a dock or piling and mounts easily in a boathouse, under a canopy, or on an open dock. Black guide post bumpers and guideposts come standard on all models.


(1) #15201 – BH-360 Fresh Water PWC Lift Main Housing
(1) #09008 – 26′ 1/4″ Galvanized Cable w/ Swaged Loop
(1) #15205 – BH-360 Galvanized Hardware & Fastener Kit
(1) #07228 – Elite 3/4 HP 56 Frame Wired PWC Lift Motor
(1) #04779 – Enclosed Belt-Driven 1500 lb. PWC Hoist Gearbox
(1) #70005 – PWC Belt Driven Hoist Cover
(1) #15211 – BH-360 PWC Lift 70″ Carpeted Bunk Set
(2) #15215 – 40″ White PVC Guide Post
(2) #96647 – 36″ Black Guide Post Bumper
(1) #36433 – PWC Hoist Cover
(1) – BH-360 Ride Pipe (Depends on Size Choosen)

Fresh Water vs. Salt Water

Fresh water pwc lifts come with galvanized hardware for the housing rollers. Salt water pwc lifts come with stainless steel hardware for the housing rollers.

Freight Shipping Policy

Questions about shipping? Review our shipping policy.


Shipping Weight 515 lbs. Total
Shipping Method Freight Only
Shipping Pieces 1 Pallet & One Loose Beam (Ride Pipe)
Hoist Capacity 1500 lbs.
Lift Capacity 1250 lbs.
Motor 3/4 HP Painted w/ Spring Switch
Cable 1/4" Compounded
Lift Speed Up to 2 ft./min.
Ride Pipe Measures 6-12 ft. from Deck to Bottom / 32" Above Deck
Main PWC Frame 6 3/8" x 32" x 36"
Bunk Mount Frame 50 1/2" x 36"
Rollers 4
Bunks (2)
Bunk Top Marine Carpet
Dock Mount Plate 24" x 3" x 7"
Pile Mount Bracket (1) 18 1/2" x 1 1/2" x 4 1/2"
Pile Mount For Up to 8" Piling
Bunk Width Fully Adjustable
Hoist #15204 - 1,500 lb. Enclosed Belt Driven PWC Hoist
Voltage: 120 Volts
Amps 20 Amp Circuit

BH-USA BH360 PWC lift should only be used to lift PWC up to 1250 lbs. The lift should not be altered in any way to lift wider boats. Never ride a PWC lift or any lift up or down. BH-USA lifts and hoists are not for lifting people in any way. BH-360 lifts must be installed pr BH-USA lift guide. Ride pipe should penetrate clay bottom at least 18” plus use pile mount with dock mount. Extra pile mounts are available. Never attempt to operate H-360 with an extension cord or generator. Mount lift switch in location that cannot be reached from PWC.

Tech Guides


11 reviews for BH-360 Fresh Water Belt Driven PWC Lift

Rated 4.18 Out of 5

5 star
4 star
3 star
2 star
1 star

  1. Raymond Smith

    The BH-360 is the only PWC lift that I will install on Lake Livingston. I have installed well over 100 now and we never have issues or call backs… Cat 5 Boat Lifts 936-327-2026

  2. Charles Holland (verified owner)

    The 360 lift is well designed and is very high quality constructed, especially the welds. The instructions could have been clearer, but I was able to install the lift without issues. The only problem I had was with Federal Express and their horrible customer service. BH-USA DELIVERED quickly and my order was complete.

  3. Emmett

    I am giving this lift a great review because it’s installed and working great and the 360 feature is nice. Also I got top notch service from BH, ordering on a Monday and receiving the lift via freight the following Friday. However, I feel there are a couple of minor areas for product improvement. First the slotted motor mounting should have a jack screw for easily adjusting the belt. The manual doesn’t give any guidance for the belt tension. Also the screws for mounting the cover are apparently the wrong size, as they stripped almost immediately (don’t worry I know how to tighten small screws properly without overtightening). I believe the tapped holes are 8-32 and the screws provided were 6-32. The top right screw is too long and hits the end of the worm shaft. I would recommend going to a #10-32 thread for the cover with some shorter large head screws.

  4. Regina Johnson

    Clients seem to like them and we are ordering more everyday.

  5. Larry Wurn

    Five star. What a great lift, and a great company to deal with! I have been building docks my entire life, and I LOVE the products rom BH-USA. Warm, gracious and knowledgable staff as well. Fabulous booklets explaining installation made the installation a dream job. Will definitely be getting more from this Company. Thank you for building such a high quality (and innovative) product.

Email Cart
Your Shopping Cart will be saved and you'll be given a link. You, or anyone with the link, can use it to retrieve your Cart at any time.
Back Email Cart
Your Shopping Cart will be saved with Product pictures and information, and Cart Totals. Then send it to yourself, or a friend, with a link to retrieve it at any time.
Your cart email sent successfully :)