Important Information About BH-USA Operations & Ordering during the Coronavirus Pandemic

8,500 lb. Advanced Dual Pulley Gear Plate Assembly

  • Made in the USA
  • No Steel on Steel Moving Parts
  • 8500 lb. Straight Line Capacity
  • Industry Standard Mounting Holes
  • Tested Under Load Before Ship

From$630.24

Clear Selection and Start Over

About this Item

  • Made in the USA
  • No Steel on Steel Moving Parts
  • 8500 lb. Straight Line Capacity
  • Industry Standard Mounting Holes
  • Tested Under Load Before Ship

8,500 lb. Advanced Dual Pulley Gear Plate Assembly

The 8,500 lb. Advanced Dual Pulley Gear Plate Assembly features no steel on steel moving parts. 8,500 lb. rating. Includes aluminum extended block assembly, 96-tooth bronze worm gear assembly, 10 in. aluminum die-cast dual belt hoist pulley, AX-34 – 34″ flat-plate hoist drive belt, and your choice of backplate type.

Aluminum Extended Block Assembly

The Aluminum Extended Block Assembly mounts directly to the gear plate. Used in flat-plate hoists. The assembly is used on BH-USA Deluxe & Advance style flat-plate hoists. Includes worm gear, drive shaft, ball bearings, and collars for mounting. Preassembled and greased for quick replacement on the hoist. Includes aluminum fasteners. Bronze or steel worm options. Fits any BH-USA gear plates and flat plate hoists.

96 Tooth Bronze Worm Gear Assembly

The 96 Tooth Bronze Worm Gear Assembly, also referred to as a bull-gear, is designed to fit any BH-USA flat-plate boat hoists. The worm gear mounts on the top of the gear plate. Grease fitting installed on the drive pipe opening. Includes install sleeve, backplate bearing with snap rings, and axle sleeve bolt. Match a bronze worm gear with a cast iron worm. Do not attempt to put a bronze gear on a bronze worm.

10″ Aluminum Die-Cast Dual Belt Hoist Pulley

The 10″ Aluminum Die-Cast Dual Belt Hoist Pulley is made from an aluminum die-casting process. Used on BH-USA Flat Plate hoists for more than 15 years. The design is much stronger in marine environments. Won’t swell or bend. Belt-gripping technology featured on the inside of the pulley helps eliminate belt slippage. Fits any known flat-plate hoists. Warping resistant. Deeper fit for drive belts. .750″ bore. Accepts up to 1/2″ drive belt. Two belt housing cast.

AX-34 – 34″ Flat Plate Hoist Drive Belt

The AX-34 – 34″ Flat Plate Hoist Drive Belt is a standard fit for BH-USA boat hoists. The belt fits around the 2 in. motor pulley and the 10 in. gear pulley. The motor mounts to the flat-plate gear plate assembly. The motor turns the motor pulley. The cogs in the belt grip and turn the gear pulley. The gear pulley turns the bushing to move the drive pipe. Tightly forms into the groves of the pulley. Designed with Anti-break technology. Cogged for true grip.

Specifications

Rated Capacity: Up to 8500 lbs.
Dimensions: 2 ft (h) x 1 ft (w)
Gear Ratio: 96:1
Back Plate Bearing: Bronze Composite
96 Tooth Gear Material: Bronze
Worm Material: Steel
Pulley: 10" Cast Aluminum Dual Pulley
Drive Belts: (2) AX-34
Weight:: 47 lbs.

Tech Guides

BH-USA Equipment Guide

Reviews

0 review for #8,500 lb. Advanced Dual Pulley Gear Plate Assembly

Email Cart
Your Shopping Cart will be saved and you'll be given a link. You, or anyone with the link, can use it to retrieve your Cart at any time.
Back Email Cart
Your Shopping Cart will be saved with Product pictures and information, and Cart Totals. Then send it to yourself, or a friend, with a link to retrieve it at any time.
Your cart email sent successfully :)

Back to Top