Important Information About BH-USA Operations & Ordering during the Coronavirus Pandemic

7,000 lb. A-Drive Enclosed Direct Drive Boat Lift Hoist

  • Enclosed aluminum gearbox & 1-1/2 hp motor
  • 7000 lb. straight-line capacity
  • No free-wheeling
  • Lubricated from factory
  • Seals & oil can be changed

From$1,049.28

Clear Selection and Start Over

About this Item

  • Enclosed aluminum gearbox & 1-1/2 hp motor
  • 7000 lb. straight-line capacity
  • No free-wheeling
  • Lubricated from factory
  • Seals & oil can be changed

7,000 lb. A-Drive Enclosed Direct Drive Boat Lift Hoist

The 7,000 lb. A-Drive Enclosed Direct Drive Boat Lift Hoist features an aluminum A-Drive 40:90 Enclosed Gearbox and an Elite Motors 1-1/2 HP stainless steel c-face boat lift motor. 7,000 lb. straight-line lift capacity. Lubricated from the factory. Features replaceable seals. Lubrication oil can be changed. 450:1 gear ratio. Stainless steel fasteners. No freewheeling. Easy to install with optional mounts. Engineered with one of the world’s largest worm gear reducer manufacturers. 16 ft. control cable. Driveshaft sold separately.

A-Drive 40:90 Enclosed Gearbox

The A-Drive 40:90 Enclosed Gearbox is a double-worm gear reducer. Features solid aluminum housing with a marine-grade finish. 450:1 ration. 7,000 lb. straight-line capacity with a 1-1/2 hp boat lift motor. Includes bronze-on-steel gears. Enclosed gears permanently lubed with BH-USA gear grease. Guaranteed not to leak. Includes output shaft with a strong cast flange mount. Uses all stainless steel fasteners. Coupled with the correct mounting plate, the gearbox can be used on both overhead boat lifts and pile mount boat lifts.

Requires a hardened output driveshaft to attach the hoist to the lift drive pipe. (sold separately)

Elite 1 1/2 HP Stainless Steel C-Face Boat Lift Motor

The Elite 1 1/2 HP Stainless Steel C-Face Boat Lift Motor is IP-55 NEMA rated, UL listed, & CSA approved. Designed with stainless steel housing with aluminum end-bells, double-shielded ball bearings, and dynamically balanced rotors. Features a TENV (totally enclosed, non-venting housing) motor housing. TENV prevents dirt and insects from entering the motor. The motor is a single-phase, dual voltage motor with C-face mounting style. The motor fits the BH-USA A-Drive direct-drive hoists, Golden Sea Drives, and other brand direct-drive hoists. Easy to follow wiring instructions. The motor has colored T-Wires. Each motor comes with a cross-reference wire chart. It does not work on flat-plate boat hoists.

BH-USA recommends using a licensed electrician to wire or rewire any electrical components.

 

Specifications

Type 40:90
Actual Ratios 450:1
Make Aluminum w/ Stainless Fasteners
Lube Special blend gear grease permanently
Motor 1.5 HP
Motor Mount C-Face
Manufacturer BH-USA
Warranty 2 Year
Motor Input Rotational 360 Degrees

Tech Guides

A-Drive Direct Drive Boat Hoist Guide

Reviews

0 review for #7,000 lb. A-Drive Enclosed Direct Drive Boat Lift Hoist

Email Cart
Your Shopping Cart will be saved and you'll be given a link. You, or anyone with the link, can use it to retrieve your Cart at any time.
Back Email Cart
Your Shopping Cart will be saved with Product pictures and information, and Cart Totals. Then send it to yourself, or a friend, with a link to retrieve it at any time.
Your cart email sent successfully :)

Back to Top