7,000 lb. A-Drive Direct Drive Boat Lift Hoist

About this Item

7,000 lb. A-Drive Direct Drive Boat Lift Hoist

The 7,000 lb. A-Drive Direct Drive Boat Lift Hoist is a 40:75 direct-drive gearbox with a double-worm gear reducer and a 1 1/2 HP boat lift motor. Features a solid aluminum gearbox housing with a marine-grade finish. 7,000 lb. straight-line capacity. 450:1 gear ratio. Includes factory lubricated with a special-blend of gear oil. Features replaceable seals. No freewheeling. Engineered with one of the world’s largest worm gear reducer manufacturers. Your choice of stainless steel or painted black finish 1 HP electric motor. Easy to install with option hoist mounts. The motor includes in-line GFCI wired to 110v or 220v with 16 ft. of control cable from motor to plug. Driveshaft sold separately.

A-Drive 40:90 Double Worm Reducer Gearbox

The A-Drive 40:90 Double Worm Reducer Gearbox is a direct-drive gearbox with a double-worm gear reducer. Features a solid aluminum gearbox housing with a marine-grade finish. 450:1 gear ratio. Add a 1 1/2 HP direct-drive c-face motor with the 40:90 gearbox to create a 7,000 lb. straight line capacity boat lift hoist. Includes bronze-on-steel gears. Enclosed gears permanently lubed with BH-USA gear grease. Guaranteed not to leak. Includes output shaft with a strong cast flange mount. Uses all stainless steel fasteners. Coupled with the correct mounting plate, the gearbox works on both overhead boat lifts and pile mount boat lifts. 5-year warranty.

The gearbox requires a hardened output driveshaft to attach the direct drive boat hoist to the boat lift drive pipe. (sold separately)

Elite 1 1/2 HP Stainless Steel C-Face Boat Lift Motor

The Elite 1 1/2 HP Stainless Steel C-Face Boat Lift Motor is a dual voltage, standard duty single-phase electric motor with a start capacitor. Stainless steel finish. Features the standard direct drive mounting hole pattern. Fits our A-Drive direct drive boat hoists and boat lifts. Fits direct drive systems like the BH-USA A-Drive Direct Drive Systems, Golden Sea Drives, and other direct drive input faces. Includes aluminum end bells. Double-shielded ball bearings. Dynamically balanced rotors. 5/8 in. motor shaft.

IP-55 NEMA 56C frame. UL listed and CSA approved. Features a totally enclosed, non-venting housing (TENV). The TENV housing helps prevent dirt and insects from getting into the electric motor. Maximum run time of 15 minutes. Easy-to-follow wiring diagrams included with the electric motor. Features colored T-wires. Includes cross-reference wire chart for all Leeson Electra-gear motors. Made by Elite Motors.

Does not work on belt-drive boat hoists or boat lifts.

Factory Electric Motors

Wired 220v from the factory. Allows for rewiring to 110v. Does not include an in-line GFCI, control cable, or drum switch.

Factory Wired Motors

Includes an inline GFCI, control cable, and drum switch. Wired to the voltage, switch type, and length of control cable selected.

BH-USA recommends using a licensed electrician to wire or rewire any electrical components.

C-Face Style Motors

A “C–Face” motor is a common American mechanical standard. Designed with a rugged flange on the face of the motor for mounting purposes. The weight of the motor is supported by the flange. Most commonly attached to a gearbox. The flange is strong enough to cantilever the motor.

The NEMA C-Face mount incorporates a machined-face flange and a pilot on the end of the shaft to allow direct coupling with equipment. Bolts pass from the mounting face through threaded holes in the motor.

BH-USA A-Drive Direct Drive Boat Hoists