Important Information About BH-USA Operations & Ordering during the Coronavirus Pandemic

4,000 lb. Standard Gear Plate Assembly

1 review
  • 4,000 lb. straight line capacity
  • Assembled and tested under load before shipping
  • No steel-on-steel moving parts
  • Includes 10 in. hoist pulley and 34 in. hoist belt
  • Features industry-standard mounting holes
  • Life Time Warranty
  • Made in the USA

From$311.98

Clear Selection and Start Over

About this Item

  • 4,000 lb. straight line capacity
  • Assembled and tested under load before shipping
  • No steel-on-steel moving parts
  • Includes 10 in. hoist pulley and 34 in. hoist belt
  • Features industry-standard mounting holes
  • Life Time Warranty
  • Made in the USA

4,000 lb. Standard Gear Plate Assembly

The 4,000 lb. Standard Gear Plate Assembly features no steel on steel moving parts. 4,000 lb. rating. Includes aluminum short block assembly, 96-tooth cast iron worm gear assembly, 10 in. aluminum die-cast hoist pulley, AX-34 – 34″ flat-plate hoist drive belt, and your choice of backplate type.

Aluminum Short Block Assembly

The Aluminum Short Block Assembly is a complete replacement worm assembly. Fits all BH-USA standard flat-plate hoists. Features industry-standard 2 inch bearing blocks. Made from marine-grade aluminum. Bronze worm installed on hardened drive shaft inside blocks from the factory. Flange bushings on blocks. Easy-to-reach grease fittings. Easy replacement for worn out worms on older gear plates. Hardware included. Aluminum worm cover included.

96 Tooth Cast Iron Worm Gear Assembly

The 96 Tooth Cast Iron Worm Gear Assembly, also referred to as a bull-gear, is designed to fit any BH-USA flat-plate boat hoists. The worm gear mounts on the top of the gear plate. Grease fitting installed on the drive pipe opening. Includes install sleeve, backplate bearing with snap rings, and axle sleeve bolt. Match a cast iron gear with a steel bronze worm.

10″ Aluminum Die-Cast Hoist Pulley

The 10″ Aluminum Die-Cast Hoist Pulley is made from an aluminum die-casting process. Used on BH-USA Flat Plate hoists for more than 15 years. The design is much stronger in marine environments. Won’t swell or bend. Belt-gripping technology featured on the inside of the pulley helps eliminate belt slippage. Fits any known flat-plate hoists. Warping resistant. Deeper fit for drive belts. .750″ bore. Accepts up to 1/2″ drive belt.

AX-34 – 34″ Flat Plate Hoist Drive Belt

The AX-34 – 34″ Flat Plate Hoist Drive Belt is a standard fit for BH-USA boat hoists. The belt fits around the 2 in. motor pulley and the 10 in. gear pulley. The motor mounts to the flat-plate gear plate assembly. The motor turns the motor pulley. The cogs in the belt grip and turn the gear pulley. The gear pulley turns the bushing to move the drive pipe. Tightly forms into the groves of the pulley. Designed with Anti-break technology. Cogged for true grip.

Specifications

Rated Capacity: 4,000 lbs.
Tested Capacity: Straight line
Gear Plate Dimensions: 2 ft. x 1 ft.
Bull Gear Ratio: 96:1
Back Plate Bearing: Bronze Composite
96 Tooth Gear Material: Cast Iron
Worm Material: Hardened Bronze
Hoist Pulley Size: 10 in.
Hoist Pulley Material: Zinc die-cast
Drive Belt Size: 34 in.
Drive Belt Type: AX-34 cogged belt
Weight: 34-47 lbs.
Warranty: Lifetime
Manufacturer: BH-USA

Tech Guides

BH-USA Equipment Guide

Reviews

1 review for 4,000 lb. Standard Gear Plate Assembly

Rated 5 Out of 5

5 star
100%
4 star
0%
3 star
0%
2 star
0%
1 star
0%

  1. This is a top quality aluminum gear plate. Well packaged and shipped quickly.

    Fourchonman

Email Cart
Your Shopping Cart will be saved and you'll be given a link. You, or anyone with the link, can use it to retrieve your Cart at any time.
Back Email Cart
Your Shopping Cart will be saved with Product pictures and information, and Cart Totals. Then send it to yourself, or a friend, with a link to retrieve it at any time.
Your cart email sent successfully :)

Back to Top